Holley EFI Terminator X Fox Body Mustang 5.0 MPFI Kit, TFI Distributor, EV1 Injectors (1987-1993)
Racing Use Only, Not Legal for Road Use
This is the Terminator X kit built for the Fox Body Mustang with the factory 302 and the stock TFI distributor. The Fox Body specific main harness, the TFI ignition adapter and an EV1 injector harness that directly replaces the factory Ford injector harness make it a plug and play swap from the stock computer on 1987-1993 cars. You also get the Terminator X ECU with its mounting bracket, MAT and CTS sensors, a Bosch LSU 4.9 wideband and the 3.5 in touchscreen handheld, so the whole thing can be set up without a laptop. It controls fuel and spark only: no drive by wire and no transmission control, so it suits cars with a manual or non electronic automatic transmission. Short term and long term fuel correction help keep the fuel table in line, but that is not a replacement for a proper calibration; someone experienced still needs to dial in the base tune, timing and safeties to get the most out of it.
Features
- Plug and play with 1987-1993 Fox Body Mustangs powered by the factory 302ci Small Block Ford with the stock TFI distributor
- Fox Body specific engine main harness, TFI ignition adapter, ECU mounting bracket, MAT and CTS sensors
- EV1 injector harness directly replaces the factory Ford injector harness
- High impedance injector drivers power most stock injectors and Holley EFI injectors
- Bosch LSU 4.9 wideband oxygen sensor for closed loop fuel control
- Built in 1 bar MAP sensor with 1/8 in, 3/16 in and 1/4 in vacuum hose adapters; for boosted applications the internal MAP can be disabled and the harness comes with a terminated connector for an external MAP sensor
- Plug and play ignition with Holley Dual Sync and HyperSpark distributors (HyperSpark requires adapter 558-323)
- 4 programmable inputs (12V, ground, 5V and frequency) for extra pressure sensors, nitrous activation, trans brake and similar triggers
- 4 programmable outputs (ground and PWM) for electric fans, boost control solenoid, nitrous control, IAC and more
- Boost control: boost vs time, gear, RPM and speed, plus boost safeties
- Nitrous control: single channel wet or dry, progressive or non progressive, rich and lean safeties, target closed loop AFR
- Advanced tables: 4x 1D, 1x 1D per gear, 4x 2D and 1x 2D per gear for custom functions such as flex fuel offset or fuel and oil pressure safeties
- On board diagnostic LEDs for ECU power, engine run, wideband status, TPS calibration, crank signal and cam signal
- 3.5 in touchscreen handheld with calibration wizard, internal datalogging and customizable gauge display
- Compact ECU that mounts almost anywhere (diagnostic LEDs must face up)
- Free Holley EFI tuning software for full laptop access
Specifications
| Part number | 550-937F |
| System | Terminator X |
| Engine | Ford Small Block, factory 302ci (5.0L) |
| Ignition type | Ford TFI |
| Injector connector | EV1 (Jetronic / Minitimer) |
| Injector drivers | High impedance |
| Wideband | Bosch LSU 4.9 |
| MAP sensor | Internal 1 bar, external MAP connector provided |
| Drive by wire | No |
| Transmission control | None |
| Inputs / outputs | 4 inputs, 4 outputs |
| Handheld | 3.5 in touchscreen |
Fitment
1987-1993 Fox Body Mustang with the factory 302ci Small Block Ford and the stock TFI distributor. Holley catalogs this kit under 1979-1993 Ford Mustang, but the plug and play fitment is the 1987-1993 cars. Fuel injectors, distributor, idle air control motor and throttle position sensor are not included. If you keep the Ford OEM TPS and IAC, the Ford connectors have to be wired in (not included). No drive by wire and no transmission control. Racing use only, not legal for use on emissions controlled vehicles.
What is included
- Terminator X ECU
- ECU mounting bracket
- Fox Body specific engine main harness
- EV1 injector harness
- TFI ignition adapter
- ECU main power harness
- MAT and CTS sensors
- Bosch LSU 4.9 wideband oxygen sensor
- 3.5 in touchscreen handheld
- Terminated connector for external MAP sensor
- Vacuum hose adapters (1/8 in, 3/16 in, 1/4 in)