Holley EFI Terminator X LS MPFI Kit, 24x Crank, EV6 Injectors (GM LS1/LS6)
Racing Use Only, Not Legal for Road Use
This is the Terminator X kit for 24x LS engines running EV6 injectors. You get the Terminator X ECU, the plug and play 24x LS main harness, an EV6 (USCAR) injector harness, a Bosch LSU 4.9 wideband and the 3.5 in touchscreen handheld, so the whole thing can be set up without a laptop. It controls fuel and spark only: no drive by wire and no transmission control, so it suits cable throttle engines with a manual or non electronic automatic transmission. Short term and long term fuel correction help keep the fuel table in line, but that is not a replacement for a proper calibration; someone experienced still needs to dial in the base tune, timing and safeties to get the most out of it.
Features
- Plug and play engine control for GM LS1/LS6 engines with a 24x crank reluctor and EV6 injectors
- High impedance injector drivers power most stock LS injectors and Holley EFI injectors (does not control low impedance injectors)
- Bosch LSU 4.9 wideband oxygen sensor for closed loop fuel control
- Built in 1 bar MAP sensor with 1/8 in, 3/16 in and 1/4 in vacuum hose adapters; for 2 bar and up, Holley recommends GM MAP sensor 12592525 with adapter harness 558-416
- 4 programmable inputs (12V, ground, 5V and frequency) for extra sensors, nitrous activation, trans brake and similar triggers
- 4 programmable outputs for items such as electric fans, a boost control solenoid or nitrous control
- Boost control: boost vs time, gear, RPM and speed, plus boost safeties
- Nitrous control: single channel wet or dry, progressive or non progressive, rich and lean safeties, target closed loop AFR
- Advanced tables: 4x 1D, 1x 1D per gear, 4x 2D and 1x 2D per gear for custom functions
- On board diagnostic LEDs for ECU power, engine run, wideband status, TPS calibration, crank signal and cam signal
- 3.5 in touchscreen handheld with calibration wizard, internal datalogging and customizable gauge display
- Compact ECU that mounts almost anywhere (diagnostic LEDs must face up)
- Compatible with Holley EFI accessories such as gauges, shift lights, modules and Holley digital and Pro dashes
- Free Holley EFI tuning software for full laptop access
Specifications
| Part number | 550-909 |
| System | Terminator X |
| Engine | GM LS1/LS6, 24x crank reluctor, 1x cam |
| Ignition type | GM LS 24x, coil per cylinder |
| Injector connector | USCAR (EV6) |
| Injector drivers | High impedance |
| Wideband | Bosch LSU 4.9 |
| MAP sensor | Internal 1 bar |
| Drive by wire | No |
| Transmission control | None |
| Inputs / outputs | 4 inputs, 4 outputs |
| Handheld | 3.5 in touchscreen |
Fitment
GM LS1/LS6 engines with a 24x crank reluctor, 1x cam signal and EV6 (USCAR) injectors. Cable throttle only, no drive by wire and no transmission control. Not for low impedance injectors. Not legal for use on emissions controlled vehicles.
What is included
- Terminator X ECU
- 24x LS engine main harness
- EV6 injector harness
- ECU main power harness
- Input / output harness
- Bosch LSU 4.9 wideband oxygen sensor
- 3.5 in touchscreen handheld
- Assorted vacuum hose adapters